View MP04TT500_62900.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MP04TT500
MP04TT500
Dual Thyristor Water Cooled Module Advance Information
DS5446-1.2 May 2001
FEATURES
s s s s s s
Dual Device Module Electrically Isolated Package Pressure Contact Construction International Standard Footprint Alumina (Non Toxic) Isolation Medium Integral Water Cooled Heatsink
KEY PARAMETERS VDRM IT(AV)(per arm) ITSM(per arm) IT(RMS)(per arm) Visol
2800V 480A 11200A 753A 3000V
5 (G1)
4 (K1) 3 (A) 1 (AK) 2 (A)
APPLICATIONS
s s s s
6 (G2)
7 (K2)
Motor Control Controlled Rectifier Bridges Heater Control AC Phase Control
Fig. 1 TT Circuit diagram
VOLTAGE RATINGS
Type Number Repetitive Peak Voltages VDRM VRRM V 2800 2700 2600 2500 Conditions
MP04TT500-28 MP04TT500-27 MP04TT500-26 MP04TT500-25
Tvj = 0 to 125C, IDRM = IRRM = 50mA VDSM = VRSM = VDRM = VRRM + 100V respectively Module outline type code: MP04-W3 Module outline type code: MP04-W3A
Lower voltage grades available
ORDERING INFORMATION
Order As: MP04TT500-XX-W2 MP04TT500-XX-W3 MP04TT500-XX-W3A 1/4 - 18 NPT connection 1/4 - 18 NPT connection 1/4 - 18 NPT water connection thread
XX shown in the part number about represents VDRM/100 selection required, eg. MP04TT500-27-W2 Note: When ordering, please use the complete part number. Module outline type code: MP04-W2 (See Package Details for further information) Fig. 2 Module package variants - (not to scale)
1/10
www.dynexsemi.com
MP04TT500
ABSOLUTE MAXIMUM RATINGS - PER ARM
Stresses above those listed under 'Absolute Maximum Ratings' may cause permanent damage to the device. In extreme conditions, as with all semiconductors, this may include potentially hazardous rupture of the package. Appropriate safety precautions should always be followed. Exposure to Absolute Maximum Ratings may affect device reliability. Symbol IT(AV) Parameter Mean on-state current Test Conditions Half wave resistive load, 4.5 Ltr/min IT(RMS RMS value Twater (in) = 25C @ 4.5 Ltr/min Twater (in) = 40C @ 4.5 Ltr/min ITSM I2t ITSM I2t Visol Surge (non-repetitive) on-current I2t for fusing Surge (non-repetitive) on-current I2t for fusing Isolation voltage 10ms half sine, Tj = 125C VR = 0 10ms half sine, Tj = 125C VR = 50% VDRM Commoned terminals to base plate. AC RMS, 1 min, 50Hz Twater (in) = 25C Twater (in) = 40C Max. 540 480 845 753 11.25 633 x 103 9 506 x 103 3000 Units A A A A kA A2s kA A2s V
THERMAL AND MECHANICAL RATINGS
Symbol Rth(j-w) Parameter Thermal resistance - junction to water (per thyristor) Test Conditions dc, 4.5 Ltr/min Half wave, 4.5 Ltr/min 3 Phase, 4.5 Ltr/min Tvj Tstg Virtual junction temperature Storage temperature range Screw torque Mounting - M6 Electrical connections - M10 Reverse (blocking) Min. -40 6 (53) Max. 0.102 0.106 0.112 125 125 Units C/kW C/kW C/kW C C Nm (lb.ins)
12 (106) Nm (lb.ins)
2/10
www.dynexsemi.com
MP04TT500
DYNAMIC CHARACTERISTICS
Symbol IRRM/IDRM dV/dt dI/dt Parameter Peak reverse and off-state current Linear rate of rise of off-state voltage Rate of rise of on-state current Test Conditions t VRRM/VDRM, Tj = 125C To 67% VDRM, Tj = 125C From 67% VDRM to 500A, gate source 10V, 5 tr = 0.5s, Tj = 125C VT(TO) rT Threshold voltage. (See note 1) On-state slope resistance. (See note 1) At Tvj = 125C At Tvj = 125C 0.91 0.65 V m Min. Max. 50 1000 500 Units mA V/s A/s
Note 1: The data given in this datasheet with regard to forward voltage drop is for calculation of the power dissipation in the semiconductor elements only. Forward voltage drops measured at the power terminals of the module will be in excess of these figures due to the impedance of the busbar from the terminal to the semiconductor.
GATE TRIGGER CHARACTERISTICS AND RATINGS
Symbol VGT IGT VGD VFGM VFGN VRGM IFGM PGM PG(AV) Parameter Gate trigger voltage Gate trigger current Gate non-trigger voltage Peak forward gate voltage Peak forward gate voltage Peak reverse gate voltage Peak forward gate current Peak gate power Mean gate power Test Conditions VDRM = 5V, Tcase = 25oC VDRM = 5V, Tcase = 25oC At VDRM Tcase = 125oC Anode positive with respect to cathode Anode negative with respect to cathode Anode positive with respect to cathode See table fig. 5 Max. 3.5 200 0.25 30 0.25 5 10 150 10 Units V mA V V V V A W W
3/10
www.dynexsemi.com
MP04TT500
2500 Measured under pulse conditions
25
1: Tj = 125C Min 2: Tj = 125C Max 1 2
I2t = I2 x t 2 20
Peak half sine wave on-state current - (kA)
Instantaneous on-state current, IT - (A)
2000
1500
15
400
I2t value - (A2s x 103)
1000
10 I2t
350
500
5
300
0 0.5
1.0 1.5 2.0 Instantaneous on-state voltage, VT - (V)
2.5
0 1 ms
10
1
2 3 45
10
250 20 30 50
Cycles at 50Hz Duration
Fig. 3 Maximum (limit) on-state characteristics
100
Fig. 4 Surge (non-repetitive) on-state current vs time (with 50% VRSM at Tcase = 125C)
0.12
Thermal resistance, Junction to water, Rth(j-w) - (C/W)
Gate trigger voltage VGT - (V)
Pulse width Frequency Hz Table gives pulse power PGM in Watts s 50 100 400 100 150 150 150 200 150 150 125 500 150 150 100 1ms 150 100 25 10ms 20 - -
0.1
0W 10 W 50
W 20 W 10 5W
10
0.08
U
1
rl ppe
imi
t 99
%
0.06
0.04
Tj = 25C Tj = -40C
Region of certain triggering
VGD
Lo
lim wer
it 99
%
Tj = 125C
0.02
0.1 0.001
0.01
0.1
1
10 IFGM
0 0.001
0.01
0.1
Gate trigger current, IGT - (A)
1 10 Time (Seconds)
100
1000
Fig. 5 Gate characteristics
Fig. 6 Transient thermal impedance - dc
4/10
www.dynexsemi.com
MP04TT500
2200 2000 1800
Power dissipation (Watts, per arm)
2200
30 60 90 120 180
Power dissipation (Watts, per arm)
2000 1800 1600 1400 1200 1000 800 600 400 200 0
30 60 90 120 180 DC
1600 1400 1200 1000 800 600 400 200 0 0 100 200 300 400 500 600 700 800 900 1000 Sine wave current (Average, per arm)
0
200 400 600 800 1000 1200 Square wave current (Average, per arm)
1400
Fig. 7 On-state power loss per arm vs on-state current at specified conduction angles, sine wave 50/60Hz
100 90
Maximum permissble inlet water temperature - (C)
Fig. 8 On-state power loss per arm vs on-state current at specified conduction angles, square wave 50/60Hz
100
Maximum permissible water inlet temperature - (C)
30 60 90 120 180
90 80 70 60 50 40 30 20 10 0
80 70 60 50 40 30 20 10 0 0
30 60 90 120 180 DC
100
200
300
400
500
600
0
100
Sine wave current (Average, per arm)
200 300 400 500 600 700 Square wave current (Average, per arm)
800
Fig. 9 Maximum permissible water inlet temperature vs onstate current at specified conduction angles, sine wave 50/60Hz
Fig. 10 Maximum permissible water inlet temperature vs onstate current at specified conduction angles, square wave 50/60Hz 5/10
www.dynexsemi.com
MP04TT500
4000
90
6000
3500
80
5000 Max permissible water inlet temp. - (C)
3000 70
90 Total device power loss - (W) Max permissible water inlet temp. - (C) 4000 80 70 3000 60 50 2000 40 30 1000 20 Power resistive or inductive load 10 Temp resistive or inductive load 0 900 1000 1100 1200 1300 1400 1500
Total device power loss - (W)
2500
60
2000
50
1500
40
1000 Power resistive load Power inductive load Temp resistive load Temp inductive load 500
30
500
20
0 400
10 600 700 800 900 1000 1100 1200 DC bridge output current - (A)
0 600
700
800
DC bridge output current - (A)
Fig. 11 50/60Hz single phase bridge DC output current vs power loss and maximum permissible water inlet
Fig. 12 50/60Hz three phase bridge DC output current vs power loss and maximum permissible water inlet
6/10
www.dynexsemi.com
MP04TT500
PACKAGE DETAILS
For further package information, please visit our website or contact your nearest Customer Service Centre. All dimensions in mm, unless stated otherwise. DO NOT SCALE.
Recommended fixings for mounting: M6 socket head cap screws Nominal weight: 2060g Auxiliary gate/cathode leads not supplied as standard, but maybe purchased separately. Module outline type code: MP04-W2
7/10
www.dynexsemi.com
MP04TT500
PACKAGE DETAILS
For further package information, please visit our website or contact your nearest Customer Service Centre. All dimensions in mm, unless stated otherwise. DO NOT SCALE.
Recommended fixings for mounting: M6 socket head cap screws Nominal weight: 2060g Auxiliary gate/cathode leads not supplied as standard, but maybe purchased separately. Module outline type code: MP04-W3
8/10
www.dynexsemi.com
MP04TT500
PACKAGE DETAILS
For further package information, please visit our website or contact your nearest Customer Service Centre. All dimensions in mm, unless stated otherwise. DO NOT SCALE.
Recommended fixings for mounting: M6 socket head cap screws Nominal weight: 2530g Auxiliary gate/cathode leads not supplied as standard, but maybe purchased separately. Module outline type code: MP04-W3A
9/10
www.dynexsemi.com
MP04TT500
POWER ASSEMBLY CAPABILITY
The Power Assembly group provides support for those customers requiring more than the basic semiconductor switch. Using CAD design tools the group has developed a flexible range of heatsink / clamping systems in line with advances in device types and the voltage and current capability of Dynex semiconductors. An extensive range of air and liquid cooled assemblies is available covering the range of circuit designs in general use today.
HEATSINKS
The Power Assembly group has a proprietary range of extruded aluminium heatsinks. These were designed to optimise the performance of Dynex semiconductors. Data with respect to air natural, forced air and liquid cooling (with flow rates) is available on request. For further information on device clamps, heatsinks and assemblies, please contact your nearest sales representative or customer service office.
http://www.dynexsemi.com e-mail: power_solutions@dynexsemi.com
HEADQUARTERS OPERATIONS DYNEX SEMICONDUCTOR LTD Doddington Road, Lincoln. Lincolnshire. LN6 3LF. United Kingdom. Tel: 00-44-(0)1522-500500 Fax: 00-44-(0)1522-500550 DYNEX POWER INC. 99 Bank Street, Suite 410, Ottawa, Ontario, Canada, K1P 6B9 Tel: 613.723.7035 Fax: 613.723.1518 Toll Free: 1.888.33.DYNEX (39639) CUSTOMER SERVICE CENTRES Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33 North America Tel: 011-800-5554-5554. Fax: 011-800-5444-5444 UK, Scandinavia & Rest Of World Tel: +44 (0)1522 500500. Fax: +44 (0)1522 500020 SALES OFFICES Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33 North America Tel: (613) 723-7035. Fax: (613) 723-1518. Toll Free: 1.888.33.DYNEX (39639) / Tel: (949) 733-3005. Fax: (949) 733-2986. UK, Scandinavia & Rest Of World Tel: +44 (0)1522 500500. Fax: +44 (0)1522 500020 These offices are supported by Representatives and Distributors in many countries world-wide. (c) Dynex Semiconductor 2001 Publication No. DS5446-1 Issue No. 1.2 May 2001 TECHNICAL DOCUMENTATION - NOT FOR RESALE. PRINTED IN UNITED KINGDOM
Datasheet Annotations: Dynex Semiconductor annotate datasheets in the top right hard corner of the front page, to indicate product status. The annotations are as follows:Target Information: This is the most tentative form of information and represents a very preliminary specification. No actual design work on the product has been started. Preliminary Information: The product is in design and development. The datasheet represents the product as it is understood but details may change. Advance Information: The product design is complete and final characterisation for volume production is well in hand. No Annotation: The product parameters are fixed and the product is available to datasheet specification.
This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners.
10/10
www.dynexsemi.com

▲Up To Search▲

Price & Availability of MP04TT500

	To Download MP04TT500 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .